Archive › Generales

Edgebanding considerations when using CutRite

Do I model with edgebanding included in the parts or do I model the raw parts and add edgebanding are parts to my assembly?  Do I have to make two models?

Modelling parts which may or may not be edge banded (depending on materials) pose a challenge when it comes to other software which may be part of a production flow.  This is particularly challenging when both sets of programs / files  are always sent to the shop and the flow is chosen on the floor.

Take for example a shelf which may be made or oak or  a plywood of some kind.  In the case of the plywood the 2 visible edges would need edgebanding, in the case of oak however it would not be.

Ideally the model of the part would be the same and therefore so would the program IF all possible production streams are equal.  But … Read the rest

Comentarios desactivados en Edgebanding considerations when using CutRite

Tool Visualization

Process by Process

By far the fastest way to verify the programs do not have ‘basic’ programming errors would be to ‘see’ what has been programmed.  ONGAA CAM now shows a reasonable representation of the tool in is starting position.  The tool dimensions are taken from the Tool Database and are shown with the programmed compensation, depth (or through depth).  This will help in ensuring tool compensations are correct as well as showing potentially unexpected interference with other areas of the part.

Tools that are incorrectly identified appear as red tools of a standard diameter where as all recognized tools appear as green.

V Drill, V Route, V Pocket, V Saw, H Drill are all supported.


Full simulation

Simulation Animation

Once all the processes have been defined, a simulation of all machining is available.

Read the rest

Comentarios desactivados en Tool Visualization

Nesting interface improvements

The ONGAA CAM nesting interface has been improved to provide easier manual movement of parts as well as allowing renestiong of single sheets (in a multi sheet nests).


The initial view of the nest remains the same with the first 4 sheets displayed.  By double clicking on any sheet a full screen view of the sheet is displayed.  Both the initial 4 sheet and the single sheet now includes the sheet scrap material and also left and right mouse button drag & drop movement.  If the sheet boundary is exceeded both the part and the sheet scrap boundary are highlighted to indicate this.


An option has been added to allow renesting of a single sheet for those times when then nesting strategy works for most sheets but not all.

The renest option also allows you to resize the ‘working area’ of a sheet and/or change the strategy … Read the rest

Comentarios desactivados en Nesting interface improvements

MPR Naming from Custom Properties

MPR creation is often only one step in the overall manufacturing process.  The flow from ERP to program generation to ‘production’ to post production steps often relies on filenames to connect the steps.

In ONGAA CAM MPR names are traditionally based on the model name.  This poses a challenge when ‘other software’ cannot read a longer filename or when the programs need to adhere to a specific naming convention that is not related to the SolidWorks part names.  This situation is particularly relevant when MPR programs on the shop floor come from a library rather than generated each time they are needed.  Orders arrive on the floor with product codes and quantities.  For example:

86400-02 QTY 30

86300-04 QTY 30

With properly created barcodes on the orders, these are efficient and accurate for loading jobs.

For this reason, ONGAA CAM has a new feature to read SOLIDWORKS custom properties to … Read the rest

Comentarios desactivados en MPR Naming from Custom Properties

Reset the SolidWorks Planes to Z axis up — and call that the Top.

From those of us that are accustomed to working in ‘Machine Space’, the Z-Axis is always UP.   So why on earth does SolidWorks insist that Y is up?

Rather that ask and then answer the question, I’d would rather show you how to change it.  What we will do in the steps below is reset the default views and rename the default planes for both parts and assemblies and save the changes into the Part and Assembly templates.


Open Solidworks and create a new PART

The default view is most likely trimetric view and look like this.

We will be using the Triad to change and verify the views we want in several steps.




First, change to the Front View.  Use Ctrl-1 or the Heads-up menu or Spacebar
The Triad should look like this.






Now use the Spacebar to get access … Read the rest

Comentarios desactivados en Reset the SolidWorks Planes to Z axis up — and call that the Top.

ONGAA CAM Generates MRPs in Inches

INCHES for Operators

Although the ‘underlying’ Units of measure of both SOLIDWORKS and WoodWOP are metric, this does not help operators accustomed to units in Inches.

Since one of the 4 ‘Guiding Mandates’ of ONGAA CAM is ‘ allow the operator to perform all operations as before’, we felt we should do something about this.

As of version 1.3.34, ONGAA CAM generates WoodWOP programs in Inches.  This is independent of the Units of Measure of the model or programming units.  Simply turn the option ON and ONGAA CAM creates the MPR with the WoodWOP Inch indicator ON and values in inches.  All ‘geometric measures’ are converted to Inches as the MPR is generated.  This includes all X,Y,Z locations, distances, radii and depths.

It should be noted that, at this time, programming in ONGAA CAM is still in metric (expected and displayed).  This ensures that all programs (old and new) will … Read the rest

Comentarios desactivados en ONGAA CAM Generates MRPs in Inches

ONGAA CAM for Biesse – Nesting module is now available

With the release of 1.3.12 of ONGAA CAM for Biesse, the optional nesting module is now available.

The Nesting Option provides the ability to nest complete assemblies at one time. Nesting features include 8 fill/nest options auto nesting, grain alignment, manual moves after auto nesting, tool change / free motion optimization and automatic sheet splitting based on named material and material thickness.  Up to 99 sheets can be nested at one time.  When sheet splitting is used, each material ‘sheet size’ can be selected from a sheet library.

Different options can be tried while in preview and once satisfied the layouts can be ‘Accepted’.  Printed layout sheets are also available.

A nested program is created for each sheet as a standard BPP program.  This allows the operator to make ‘on the shop floor’ changes without the need to regenerate the files etc.  This is particularly useful when tools need to … Read the rest

Comentarios desactivados en ONGAA CAM for Biesse – Nesting module is now available

WoodPrint Integration added to ONGAA CAM for labels

WoodPrintLabelONGAA CAM Nesting now integrates to the WoodPrint Label Printing allowing part information to be printed (and place) directly on the parts.

Basic part dimensions and part names plus 4 SolidWorks Custom properties and well as 4 additional custom properties intended for edge banding information are available.

With WoodPrint feature activated, ONGAA CAM produces the complete set on nested MPRs, Part MPRs and Part Images as required by WoodPrint and referred to by the CSV and PNX using the prescribed naming conventions.


The Weeke Vantech Concept series machine nesting CNC machines with the material handling option and label printing take full advantage of the WoodPrint integration by ONGAA CAM.  ONGAA CAM provides the following details for woodprint automatically at time of nesting.

  • Part Name
  • Part ID (WoodPrint identifier)
  • Part Length, Width, Thickness
  • Assembly Name
  • 4 User definable Custom properties retrieved from SOLIDWORKS
  • 4 User definable Custom properties retrieved from
Read the rest
Comentarios desactivados en WoodPrint Integration added to ONGAA CAM for labels

Nesting – Automatic separation of parts based on thickness and material

The earlier version of the nesting functions of ONGAA CAM assumed each nesting run would be for one thickness of material and it was up to the programmer to ensure parts were grouped by material and thickness.

Based on valuable customer feedback we have changed this.

As of version, ONGAA CAM can now determine if a part belongs to a nesting group based on work piece definition parameter ‘Thickness’ and on a new parameter called (Material).  Each Nested MPR created will also have a comment added which will indicate the material and the thickness used for nesting.  As before, each ‘Nested MPR’ is still a 100% compliant MPR meaning that individual processes can still be adjusted at the console.

Since material is often defines as a Custom Property within SOLIDWORKS, we have added the ability to reference the custom property name in the work piece definition.

This feature makes … Read the rest

Comentarios desactivados en Nesting – Automatic separation of parts based on thickness and material

ONGAA CAM para Biesse- En producción

ONGAA CAM – Básico para Biesse ha sido publicado!


Con ONGAA CAM básico para Biesse, puede ya programar su máquina CNC Biesse directamente de SOLIDWORKS en un ambiente 3D único/simple. Las funciones soportadas son: Taladro (vertical y horizontal), Fresado (vertical y horizontal), Cavidad (rectangular y polígonos) y Sierra.

ONGAA CAM ofrece muchas funciones que ahorran tiempo, tal como ‘Todos los taladros en cara’ selecciones de taladro que automáticamente expande un proceso ONGAA CAM único a procesos de taladro individuales en BiesseWorks.

Utilizando el poder de SOLIDWORKS para modelar, provee soluciones empresariales adicionales, porque esto también hace todos los programas paramétricos. Esto se debe a que los pasos de programación son almacenados con conocimiento del modelo. A medid que cambia el modelo, los pasos de programación son generados con nueva geometría.

Con ONGAA CAM y SOLIDWORKS realmente puede diseñarlo una sola vez y fabricar en 1000 tamaños diferentes.


Dado … Read the rest

Comentarios desactivados en ONGAA CAM para Biesse- En producción